CCTV

Showing 1-24 of 27 item(s)

Longreach II active CCTV receiver HUB Muxlab/500126 [8-PORT]

Longreach II active CCTV receiver HUB Muxlab/500126 [8-PORT] 2

CCTV Hubs Active

MUXLAB/500126 [8-PORT]

MUXLAB/500126 [8-PORT]

The LongReach II Active CCTV Receiver Hub (500126 [8p], 500127 [16p]) provides extended distance between the CCTV camera and the DVR via Cat5e/6 cable. The hub features Auto Gain Control (AGC) and supports up to 5,000 ft (1.5 km) via Cat5e/6 cable when used in conjunction with MuxLab FEATURES : 8 or 16 channel analogue CCTV hub Up to 5,000 feet (1.5...

View

CCTV IP Extender kit Muxlab/500110

CCTV IP Extender kit Muxlab/500110 2

CCTV Extenders

MUXLAB/500110

The CCTV IP Extender Kit (500110) allows any CCTV IP camera to be connected over extended distance via Cat5e or coax cable. The 500110 supports up to two IP cameras up to 650 ft (200m) at 100 Mbps and up to 1 mile (1.6km) at 25Mbps. FEATURES : Extend distance between IP camera and 10/100BaseT LAN Supports up to two (2) IP cameras Cat5e/6 or coax link Up...

View

Rgb balun Muxlab/500002

Rgb balun Muxlab/500002 2

CCTV Baluns Passive

MUXLAB/500002

The RGB Balun allows one Red, Green, Blue (RGB) or YPbPr component video channel to be transmitted via three (3) unshielded twisted pairs. Used in pairs, the RGB Balun supports RGB signals with synchronization on Green. The RGB Balun is used in a home or commercial applications as a smart, fast and cost-effective means of cabling component RGB video...

View

CCTV Pass-Thru balun Muxlab/500022

CCTV Pass-Thru balun Muxlab/500022 2

CCTV Baluns Active

MUXLAB/500022

The CCTV Pass-Thru Balun allows video, 2-wire PTZ control and remote power to be transmitted via one 4-pair Cat5e/6 cable, thus eliminating the need to install multiple cables for more efficient cabling in the CCTV security and surveillance environment. The Pass-Thru Balun may be used in pairs or in conjunction with standard twisted pair cross-connect...

View

Longreach II active CCTV receiver HUB Muxlab/500126 [8-PORT]

Longreach II active CCTV receiver HUB Muxlab/500126 [8-PORT] 2

CCTV Hubs Active

MUXLAB/500127 [16-PORT]

MUXLAB/500127 [16-PORT]

The LongReach II Active CCTV Receiver Hub (500126 [8p], 500127 [16p]) provides extended distance between the CCTV camera and the DVR via Cat5e/6 cable. The hub features Auto Gain Control (AGC) and supports up to 5,000 ft (1.5 km) via Cat5e/6 cable when used in conjunction with MuxLab FEATURES : 8 or 16 channel analogue CCTV hub Up to 5,000 feet (1.5...

View

CCTV IP Poe extender 2 packs Muxlab/500111-2PK

CCTV IP Poe extender 2 packs Muxlab/500111-2PK 2

CCTV Extenders

MUXLAB/500111-2PK

MUXLAB/500111-2PK

The CCTV IP PoE Extender allows one IP camera to be connected via a single 75-ohm coax cable in a point-to-point configuration*. The product works in pairs and the power consumption is low enough so that it does not load the PoE source or switch. The maximum distance depends on the grade of coax cable and the power consumption of the camera. Note: In...

View

Ptz balun Muxlab/500007

Ptz balun Muxlab/500007 2

CCTV Baluns Passive

MUXLAB/500007

The PTZ Balun allows CCTV video and “up-the-coax” Pan, Tilt, Zoom (PTZ) control signals to be transmitted via a single unshielded twisted pair (UTP) cable for more versatile cabling. Used in pairs, the PTZ Balun allows CCTV security and surveillance equipment to be integrated into structured cabling systems. Allows CCTV PTZ devices to be moved to any...

View

CCTV Power - Thru balun Muxlab/500024

CCTV Power - Thru balun Muxlab/500024 2

CCTV Baluns Active

MUXLAB/500024

The CCTV Power-Thru Balun allows video and remote power to be transmitted via one 4-pair Cat5e/6 cable, eliminating the need to install multiple cables for more efficient cabling in the CCTV security and surveillance environment. The Power-Thru Balun may be used in pairs or in conjunction with standard twisted pair cross-connect devices and other MuxLab...

View

Passive CCTV HUB Muxlab/500130

Passive CCTV HUB Muxlab/500130 2

CCTV Hubs Passive

MUXLAB/500130

The Passive CCTV Hub allows video, remote power and PTZ control to be transmitted via one Cat5 cable, thus eliminating the need to install multiple cables for more efficient cabling in the security video environment. 500130; with coax video output. The Passive CCTV Hub works in conjunction with the 500000, 500009, 500015, 500022, 500023, 500024, 500029...

View

CCTV IP Poe extender Muxlab/500111

CCTV IP Poe extender Muxlab/500111 2

CCTV Extenders

MUXLAB/500111

The CCTV IP PoE Extender allows one IP camera to be connected via a single 75-ohm coax cable in a point-to-point configuration*. The product works in pairs and the power consumption is low enough so that it does not load the PoE source or switch. The maximum distance depends on the grade of coax cable and the power consumption of the camera. Note: In...

View

CCTV Screw terminal balun Muxlab/500009

CCTV Screw terminal balun Muxlab/500009 2

CCTV Baluns Passive

MUXLAB/500009

The CCTV Screw Terminal Balun allows a single composite CCTV video signal to be transmitted via a single unshielded twisted pair (UTP) cable for more versatile security and surveillance cabling. Used in pairs, the CCTV Balun eliminates costly and bulky coax cable, allowing CCTV equipment to be connected via cost-effective twisted pair. The CCTV Balun may...

View

CCTV Power - Thru balun Muxlab/500024

CCTV Power - Thru balun Muxlab/500024 2

CCTV Baluns Active

MUXLAB/500029

The CCTV Power-Thru Balun allows video and remote power to be transmitted via one 4-pair Cat5e/6 cable, eliminating the need to install multiple cables for more efficient cabling in the CCTV security and surveillance environment. The Power-Thru Balun may be used in pairs or in conjunction with standard twisted pair cross-connect devices and other MuxLab...

View

Passive CCTV/GLI HUB Muxlab/500133

Passive CCTV/GLI HUB Muxlab/500133 2

CCTV Hubs Passive

MUXLAB/500133

The Passive CCTV/GLI 16-Port Hub allows video, remote power and PTZ control to be transmitted via one Cat5 cable, thus eliminating the need to install multiple cables for more efficient cabling in the security video environment. The product features full DC isolation for CCTV systems where ground loops may be present. The product works in conjunction with...

View

Longreach CCTV IP Poe extender kit Muxlab/500112

Longreach CCTV IP Poe extender kit Muxlab/500112 2

CCTV Extenders

MUXLAB/500112

The Longreach CCTV IP PoE Extender Kit allows one CCTV PoE IP camera (up to 15.4 Watts) to be connected up to 1000 ft (300 m) via a single 75-ohm coax cable in a point-to-point configuration to a PoE LAN switch. Note: If the LAN switch is not PoE, then the 48VDC Power Supply (500113) is required in order to power the PoE camera and the 500112. The...

View

CCTV Power - Thru converter balun Muxlab/500024-CNV

CCTV Power - Thru converter balun Muxlab/500024-CNV 2

CCTV Baluns Active

MUXLAB/500024-CNV

MUXLAB/500024-CNV

The CCTV Power-Thru Converter Balun allows video and remote power to be transmitted via one 4-pair Cat5e/6 cable, thus eliminating the need to install multiple cables for more efficient cabling in the analog CCTV security and surveillance environment. Additionally, the product converts 24VAC to 12VDC to allow 12VDC cameras to be remotely powered from a...

View

Passive CCTV/GLI HUB Muxlab/500133

Passive CCTV/GLI HUB Muxlab/500133 2

CCTV Hubs Passive

MUXLAB/500136

The Passive CCTV Power Integrator Hub allows video, remote power and PTZ control to be transmitted via one Cat5e/6 cable, thus eliminating the need to install multiple cables for more efficient cabling in the security video environment. The product features a built-in 16-channel 350VA CCTV power supply that supplies power to each port and works in...

View

Longreach CCTV IP Poe extender kit, 1Km Muxlab/500114

Longreach CCTV IP Poe extender kit, 1Km Muxlab/500114 2

CCTV Extenders

MUXLAB/500114

The Longreach CCTV IP PoE Extender Kit, 1Km (500114) allows one IP camera (15.4 Watts) to be connected up to 3281 ft (1000m) via a single 75-ohm coax cable in a point-to-point configuration. The maximum distance depends on the grade and quality of the coaxial cable. Typical applications: Campuses Highways Airports Hotels and Casinos,...

View

Active CCTV Transmitter balun Muxlab/500100

Active CCTV Transmitter balun Muxlab/500100 2

CCTV Baluns Active

MUXLAB/500100

The Active CCTV Transmitter Balun (500100, 500101) provides enhanced distance performance for a single CCTV video channel via Cat5 unshielded twisted pair (UTP) cable. The balun is installed at the CCTV camera and is powered by the camera power supply. There are two (2) models; 500100 for 12VDC cameras and 500101 for 24VAC cameras. Maximum distance...

View

CCTV IP POE Long Range Extender Kit, 600M Muxlab/500115

CCTV IP POE Long Range Extender Kit, 600M Muxlab/500115 2

CCTV Extenders

MUXLAB/500115

The LongReach CCTV IP PoE Extender Kit, 600m allows one IP camera (up to 30 Watts) to be connected up to 1969ft (600m) via a single 75-ohm coax cable in a point-to-point configuration. The maximum distance depends on the grade and quality of coaxial cable used, and if PoE is used. An optional 56VDC (65W) Power Supply (sold separately) can be used if...

View

Active CCTV Transmitter balun Muxlab/500100

Active CCTV Transmitter balun Muxlab/500100 2

CCTV Baluns Active

MUXLAB/500101

The Active CCTV Transmitter Balun (500100, 500101) provides enhanced distance performance for a single CCTV video channel via Cat5 unshielded twisted pair (UTP) cable. The balun is installed at the CCTV camera and is powered by the camera power supply. There are two (2) models; 500100 for 12VDC cameras and 500101 for 24VAC cameras. Maximum distance...

View

Longreach II active CCTV receiver balun Muxlab/500124

Longreach II active CCTV receiver balun Muxlab/500124 2

CCTV Baluns Active

MUXLAB/500124

The LongReach II Active CCTV Receiver Balun (500124) provides extended distance between the CCTV camera and the DVR via Cat5e/6 cable. The product features Auto Gain Control (AGC), Auto-Polarity Correction and supports up to 5,000 ft (1.5 km) via Cat5e/6 cable when used in conjunction with MuxLab Features : Up to 5,000 feet (1.5 km) via Cat5e/6 with...

View

CCTV Pass-Thru / GLI balun Muxlab/500132

CCTV Pass-Thru / GLI balun Muxlab/500132 2

CCTV Baluns Active

MUXLAB/500132

The CCTV Pass-Thru/GLI Balun allows video, remote power and 2-wire PTZ control to be transmitted via one 4-pair Cat 5 cable and is designed for installations where ground loop issues may be present. The product features ground loop isolation (GLI) and is installed either at the camera or DVR side in conjunction with other standard MuxLab CCTV baluns such...

View

Active HD CCTV received balun Muxlab/500721

Active HD CCTV received balun Muxlab/500721 2

CCTV

MUXLAB/500721

The Active HD CCTV Receiver Balun provides extended distance between an HD-SDI CCTV camera and an HD-SDI DVR via Cat5e/6 cable. The product supports up to 150 ft (45m) via Cat5e cable at HD resolution when used in conjunction with MuxLab’s HD CCTV Pass-Thru Balun (500720). Furthermore, the 500721 allows remote power and 2-wire PTZ control to be combined...

View

HD CCTV Pass-Thru balun with cable leads Muxlab/500720-CL

HD CCTV Pass-Thru balun with cable leads Muxlab/500720-CL 2

CCTV Baluns HD

MUXLAB/500720-CL

MUXLAB/500720-CL

The MuxLab 500720-CL – HD CCTV Pass-Thru Balun with Cable Leads allows one HD CCTV (HD-SDI) video channel plus remote power and PTZ control to be transmitted between the HD CCTV camera and the DVR via Cat5e/6 cable in the HD CCTV environment. The 500720-CL is used in conjunction with either another 500720-CL or with the 500700 or 500721. Features :...

View

1
2

CCTV

Product added to compare.

We use cookies to ensure that we give you the best experience on our website. If you continue to use this site, we will assume that you agree to it.